Custom trip planning and load factor software
Every trip that leaves half empty costs the same as a full one. Planners therefore look for the best combination of shipments by loading metres, weight and pallet spaces, within customers' time windows. This is often done on experience, and nobody can see afterwards whether it worked. Appfront builds custom software that assembles trips based on what actually fits, and shows per trip, customer and vehicle how full you are driving.
What is software for load building and load factor?
Software for load building and load factor helps planners combine shipments so that trips leave as full as possible, and measure afterwards how full they actually were. Load building is assembling a trip from shipments, with their loading metres, weight, pallet spaces and special requirements such as refrigerated or dangerous goods. The load factor shows what share of a vehicle's capacity was actually used. Packages such as Adaption and MendriX include load building and loading as part of their TMS. This page is for companies for whom that part calls for its own approach.
A vehicle's capacity is more than one number. The RDW (the Dutch vehicle authority) keeps records per licence plate of, among other things, the unladen mass, the maximum permitted mass, the load capacity and the maximum mass of the combination, and publishes these as open data. The length of the load floor, the number of pallet spaces, the distribution across the axles and, for example, a tail lift or refrigeration unit also matter. A trip can be full on loading metres and still have room in weight, or the other way round. If you plan on only one measure, you leave capacity unused or plan trips that do not fit.
We build software that brings this into your planning. Each shipment carries its loading metres, weight and pallet spaces from the order or the WMS, and each vehicle its capacity, supplemented with data from the RDW. The software proposes combinations that fit within time windows and capacity, and lets the planner choose. After the trip, the software compares what was planned with what was actually loaded, and shows the load factor and empty kilometres per trip, customer, vehicle and route. This shows you where things go wrong structurally, for example with a customer who always reports their shipments too late.
During planning
Combinations that fit.
After the trip
Planned versus loaded.
Over a period
Load factor per customer and route.
How we build your load building and load factor software
We start with your planning: which shipments you transport, which vehicles you use, how planners currently assemble trips and where the data on loading metres, weight and pallet spaces comes from. Then we map the capacity of your fleet. We first build the load factor calculation over completed trips, because it shows where the gains are, and have planners assess it using real trips. The load building proposals, the integration with your TMS and the reporting per customer and route follow after that.
Shipments, vehicles, way of working.
Fleet and RDW data.
Load factor of real trips.
Proposals in the planning.
What load building and load factor software actually does
The components below appear in almost every load building solution. Which ones you need depends on your cargo and how you plan now.
Shipments
Loading metres, weight, pallets.
Vehicles
Capacity per licence plate.
Load building
Combinations that fit.
Load factor
Per trip, customer and vehicle.
Empty kilometres
Where you drive empty.
Integrations
TMS, WMS, on-board computer.
Who we build load building and load factor software for
The software is meant for companies that combine many shipments every day and for whom every extra percentage point of load shows up directly in the margin. Think of a groupage company with different shipments each day, or a shipper that uses its own vehicles and hired carriers side by side.
Groupage
Many small shipments.
Distribution
Fixed routes, varying loads.
Shippers
Own and hired transport.
Construction logistics
Heavy and long loads.
Test your idea first: a working prototype in 1 day
With OneDayBuild, we make your idea tangible in a single day for €1,150, so you know whether further development is worth the investment. Decide to go ahead with the full build? Then we deduct the cost in full.
View OneDayBuild →Technology and integrations
Load building is about the cargo; the order of stops and time windows is the job of route planning software. For a full custom TMS, see building a TMS. If you use an off-the-shelf package, we build integrations with MendriX and Adaption, among others. For reviewing trips afterwards, there is trip registration software.
Why Appfront for your load building and load factor software?
The driver knows whether a trip was full, but the office rarely gets to see it. That is what we build on: first measure how full you actually drive, then give the planner suggestions that fit both load metres and weight, and make the difference visible per customer and route.
Measurable
Load per trip and customer.
Fitting
Load metres and weight together.
Planner decides
Suggestions, not obligations.
Security and privacy in load building and load factor software
The software contains data on customers, shipments and addresses, and, via trips and on-board computers, data on drivers too. We agree with you in advance who sees which data, and drivers' trip data is only used for planning and loading, not to assess individual drivers, unless you set that out differently in your policy within the GDPR.
The software runs in a European data centre, with encrypted connections and storage. Integrations with your TMS, WMS and on-board computers use protected keys that are not visible to staff, and every change to the planning is logged with time and user.
Frequently asked questions about load building and load factor software
Questions that planners and transport companies ask before building load building software.
The share of a vehicle's capacity that was actually used on a trip, measured in load metres, weight or pallet spaces. Because a trip can be full on one measure and half empty on another, the software measures them side by side.
From your own fleet data, supplemented with open data from the RDW (the Dutch vehicle authority), which lists, per licence plate, the maximum permitted mass and the payload, among other things.
The software suggests combinations that fit within capacity and time windows. The planner chooses. Planners know customers and special circumstances that are not in the data.
Yes. The software pulls orders and trips from your TMS and writes the chosen combinations back. If you use your own TMS or want one, load building can be part of it.
Route planning determines the order of stops and the times. Load building determines which shipments go together in one vehicle. In practice, the two work together.
For companies that combine many shipments every day and want to know where capacity is going to waste. If you mainly drive full loads for a single customer, the gain is smaller.
Want to know how full your trips really are?
Tell us which shipments you combine and how you plan now. We will show how custom software measures the load factor and suggests combinations that fit for your planners.